Repair CDMA phone and GSM BB5 using phoenix software

Techno and Mobile news. Pre and review, Technology, Specification, New Release, Smartphone, World Digital

Repair CDMA phone and GSM BB5 using phoenix software

17 June 2009 One Comment

Phoenix Service Software 2006, in this edition we will learn how to
the use of software. Software that can be used only with cables DKU2
and the usual DKU5 included in the purchase of mobile phone package, or can be purchased easily,
and this program is very effective in the improvement of the current mobile phone for mobile learning
or repair the phone.
The first stage of Phoenix in 2006, we run the Phoenix Icon located on the Desktop.
Logo will appear Phoenix Service Software. Asked if the User Name and Initial contents
our own hearts. and will out the view of the software main menu page.

figure 1

figure 2

Views on the main software page. There are many menus that can be used.
Among other File - Edit - Products - flashing - Tools-Windows - Help.
This menu will be increased if the phone has terdetect. For the first time use,
we must set the cable media that will be used. In Phoenix this version of the patch
only two media that can be used, namely DKU2 or DKU5. DKU2 used to
flashing Nokia BB5 new generation (DKU2 USB flashing),
while DKU5 used for the calibration, such as Nokia CDMA Unlock, Tuning Signal,
Frequency Channel Settings, edit PRL (Preffered Roaming List inject mobile phone),
phone information, etc..

figure 3

For cable DKU5 should be done before the cable installation driver page that there are
in CD, while the cable does not require drivers DKU2,
because it is a type of straight cable (connector). After DKU5 drivers installed correctly,
note on the Device Manager, on how many COM DKU5 installed.
Select File and then Manage Connections à à à Then select New Media used (DKU5 and USB).
USB to DKU2. To select Manual Setup DKU5 and specify which COM DKU5 installed.
While the USB does not need to specify DKU2 COM installation. COM DKU5 installation error
will cause the phone is connected can not detect with a good pitch.
search

figure 4

If the Manage Connection has done well,
the next step is connecting the phone to the computer using the cable page.
On this edition we will language BB5 flashing process before, for the following edition will
thoroughly explained the improvement CDMA mobile phone with this software and media DKU5.

BB5 phone that has been linked to a computer in the Offline Mode,
will to detect found new hardware on the PC, and will automatically be installed
own drivers needed. Select File à Scan Products.
But on the bottom will display software version the phone is connected

figure 5

Then click the flashing à SW Update. It will appear a new window Software Update.
Product detection in automated image RM-36 (Nokia 6680).
Before flashing the firmware we need to choose which will be used.
search

Firmware in the Nokia PC tdp on the C: \ Program Files \ Nokia \ Phoenix \ Products.
There are two ways to choose the Product Code and its only Image File (MCU) and
PPM file will automatically be selected.
Or manually select the Image File and PPM File (Language Pack).
In this case we choose the Product Code 0522048 Indonesia Silver Blue with PPM Files v36
that there is a language for product intended for Indonesian Market.
search

figure 6

After selecting the appropriate firmware has done,
note Flash Type Users have the option Restore Data (If selected then after flashing
data on the mobile phone will be returned as usual).
There are also manufactured as Product (If this is selected then the data will be deleted on the phone,
conditions so that the memory of the mobile phone will be like new.) Data does not participate in the MMC erased.
The second option is used to repair problems on the phone while the first option is used
if the phone does not have any problems, just want to upgrade it.

The next step click the Start button, then the flashing process will run by itself.
Wait until the process is finished the phone will be normal again with the firmware
that has been upgraded.

That need to be in the process of flashing this phone is a must Battery is fully charged,
never pull out the cable at the time of the flash, and downgrade the firmware version on the phone.

To downgrade the firmware version can be done APE flashing with UFS3 Box,
whereas if the mobile phone into matot error above,
it must be done FBUS flashing box that requires another,
and can not be done with this solution such as flashing.

Flashing process aims to upgrade the firmware and add the phone language
on the menu that is used if there is no previous language of choice.
While for the signal improvements, unlocking, setting frequency,
and other maintenance can be seen in the following edition.

Damage to the CDMA mobile phone is usually a total dead, Blinking, no signal, and others.
The first time that we have to do is improve the content of the data that there is
flash memory in mobile phones. With this software can do tuning and signal
other important parameter calibration. Can also backup / restore settingan channel frequency
and important data in it, and unlocking phone lock / security code.
search

Tuning Signal (To repair the signal / network)

Cases the most frequently found problem is a signal,
where the phone does not get a signal and continuously searching.
Usually this problem arises due to the data in the memory have corrupted / error.
Can also be caused by an error and reset the flashing data and open phone lock
use the other box causing this problem.
For the mobile phone will need to return the data and parameters inside again.
Tun required files in accordance with the type of mobile phone to upload into the phone.
Previous mobile phone is connected using DKU 5 cable and run the Phoenix software.

Click File à Open or Products Product Scan
Click Troubleshooting à à Read RF Parameters
Windows up to show the following:

figure 7

Click File à Load tun Find the file that matches the type Ponsel.
After the selected file name (default.tun)
Click the Write All to appear Tuning parameter file loaded successfully.
Done

Note:

Current Write means write only the CAL (Calibration) only.
Write All means all writing section is complete with CAL, and RF PANEL SET. (Recommended)
After the close tuning Read Parameters window, and the process is complete.
Mobile phone signal will appear again.
Tuning process is generally used to fix the problem on the phone CDMA signal,
especially after unlock wrong, wrong flashing with other software Flasher spt UFS3/Griffin.

UNLOCK PROCESS

- PBB Maintenance Tool set ke PKD-1RD
- Klik File à Scan Products
- Klik CDMA à Factory Value Set à Pilih Full à Klik Factory Reset

figure 8

Unlock this process does not cause the phone as well as the No Signal Flasher Software on another.
Do not Unlock PHONE CDMA UFS3 or with Griffin because it can cause the phone No Signal.
search

BACKUP DAN RESTORE PONSEL SETTING

Useful to save the settings phone settings such as channel frequency, signal, NAM, Phonebook,
and others. So that when an error occurs data on the phone (such as hang and No Signal)
can be returned as they are. If you have not previously been dibackup use
PRI is a standard file to restore it.
search

Backup data for Mobile to Computer:

Click the Read All Phone from à à Wait for the process is complete Save to File
Window will appear PRI File Header Information. Fill Product Code and Customer Name
OK.

To Restore the data to the Mobile:
Click Load From File à Select the appropriate file type PRI PHONE à Write All to Phone

figure 9

UPGRADE PRL (Roaming PREFFERED LIST)

Apply only to inject the phone. RUIM Card for mobile phone stored in the PRL is RUIM Card.
PRL is associated with the data service. If the upgrade is needed: Click on CDMA à PRL
Backup PRL: PRL Read from Phone to PRL à Save File
Restore PRL: PRL Load from File à File Search PRL needed à PRL Write to Phone

figure 10

Backup and PROCESS EDIT PHONE BOOK
Process and Edit Phone Book Backup can be easily done with
Click à CDMA Phone Book.

figure 11

PROCESS Diagnostics (CHECK CONDITION PHONE)

If required to mencheck whether Ponsel in good condition,
whether the failure of the system have occurred, such as Drop Calls, Voice and Data Connection,
Talk Time, and others.
Click Diagnostics CDMA à à Execute
Analysis: PASS showed good results.

figure 12

PROCESS ESN Reconstruction

Used at the time of the replacement IC UEM (Universal Management) or Flash IC.

No.IMEI on GSM or CDMA ESN stored in the two components, namely Flash IC and IC UEM
No Flash IC store. GSM 15-digit IMEI or ESN Decimal CDMA
(8 Digits hexadecimal digit Decimal = 10) in the Flash IC.

IC UEM record data and control the ESN / IMEI in Flash IC.
UEM IC that has been filled data / installed / damaged can only be written with the ESN / IMEI originalnya.
IC UEM is new / empty UEM can be charged only one time with the ESN / IMEI RPL option from the list you have ..

ESN / IMEI in accordance with the request can originalnya (with pay)
IMEI to the server service, so that the replacement of the UEM (no need to change if UEM IMEI ?????)

At the time of the replacement IC Flash (Case: Unknown Flash ID and Erasing Error), IMEI will be automatic?
UEM detect because Flash is the replacement IC. Therefore, after replacement
Flash IC is usually at the same time with a replacement IC UEM,
Or IMEI Original message from server (If you do not want to change UEM).
Meanwhile, at the time of the replacement IC UEM (cases Matot, No and No Audio Signal)
does not need to change the Flash IC.

File ASK (Request File) is the result of reading Uem (Read UEM) to be sent to the server IMEI.
RPL file (Reply / Response File) is a file from the original IMEI to the server is ready to write UEM.
ASK file can not be directly written to UEM, but must be sent to the server and processed into
RPL IMEInya file that matches the UEM damaged.

If the data on damage caused UEM IMEI? and a mobile phone SIM Lock
/ Phone Restricted / Invalid SIM (not want to read the SIM Card)

How to Backup UEM ASK and stored as a file:

Click generate a request file à Select exhausted replace UEM / Flash? À Select IMEI / ESN?
Fill à No IMEI / ESN originalnya and 7-digit Product Code in the Select Target
Place Request for file (Save as) where? à à then click the Start will
ASK file to be sent to the server IMEI.

How to Restore ESN / IMEI to UEM IC:

Click the Process a Response File à à Select Select UEM IMEI / ESN à Select Place for Response file
(RPL files you want to include UEM) à click Start
IMEI? will be normal again if no. IMEI is the same as the previously missing (Original)